Detailed Product Description

Features:
1) Max. seal mould proofing Silicone Sealant is a room temperature v
ulcanized sealant, has excellent adhesion to most porous surfaces with
mould proof ability, such as concrete, stone, brick, marble, cement and
ceramics
2) It adheres to clean glass, many plastics, aluminum and galvanized
steel
3) Condition request: sealant should be in temperature of 5 - 40°C
4) Its used under the relative humidity 40% - 80%
5) Too low temperature will reduce conglutination, because the sealant's
surface adhesion wetting reduce, and it can became frost ice on the
low temperature's material, it effects the sealant's conglutination
6) The standard using temperature is above 5°C
7) It has blight for the sealant in high temperature. As a result of high
temperature, the sealant will be drooping and expedite solidify time reduce
using and repair time, at the same time, it will bring air bubble. If too low
relative humidity could make the solidify speed change slow, or if too high
relative humidity could form congelation on surface of material,
it affects conglutination between the sealant and material

Common characteristic before solidify:
1) Appearance: no granule paste
2) Density: 1.38 (20 Celsius degree)
3) Skin dry time: 40 minutes (RH 50%, 25 Celsius degree)
4) Solidification time: 4 - 8 days (RH 50%, 25 Celsius degree)
5) Drooping degree: 0mm

After solidify
1) Rigidity a type sclerometer: 23
2) Elongate ratio: 100%
3) Elongate intension: 0.8Mpa
4) The data just is for consulting, but not promising

Clean process:
1) All the material should be clean out, remove dust / dirt or other feculence
2) The scour must be the solvent which was tested, if use IRA / MEK or XYLENE
which didn't demonstrate, the latter's toxicity is stronger and the other two
are better fitting
3) Elementary clean method: First, use the wettish and undepilatory pure-cotton
cloth to clean another clean cloth to clean the feculence before the solvent
volatilization, it should not dry the solvent naturally, lest should feculence
newly on the material
4) For small and deep interface, it needs to clean at full tilt
5) The material that was cleaned out should do with using lacquer, otherwise it
should be cleaned out again. If cleaned surface exposed or in the feculence,
it should be cleaned again
6) It should be changed the white cloth, which was contaminative, and it should
be raved about the impregnant from the container onto the clean cloth and it
should not put the cloth into container, otherwise the clean impregnant will
be contaminative, it will affect the result
7) It due to all the cleanout liquid are the tinder and have toxicity, it should
have good airiness condition / strictly prohibit fireworks when using them, and
adopt necessary safe system

Sealant construction process:
Common request:
1) Silicone sealant should be used in 5-40 Celsius degree, this can bring the
better effect
2) It can stick on temporary protect adhesive tape when it's necessary, if it use
the bottom-gelatinise, it must before using the sealant
3) Using the sealant should be continual, making the sealant form the columned
pile out, sealant should pile out equally, make sure it full of sealant on the
place where it need, avoid making the bubble
4) It must be decorate after using sealant, the common method is using the tools
to make overflow sealant in the direction of interface, and then beauty the
interface, make sure the interface contact equally, and then uncover all the
temporary protect adhesive tape
5) After 48 hours of using the sealant, the interface can't have the big
displacement, otherwise it will effect the result

Executive standard:
GB/T 14683-1993

Packing:
24 cartridges/carton